Icom IC-F61V UHF Two-Way Handheld Radio (discontinued)

Further details of Icom IC-F61V UHF Two-Way Handheld Radio

• The vibration function is useful when a pre-programmed 2-Tone/5-Tone signal, called by a specified ID user (BIIS mode only) or a status message (BIIS mode only) is received, the vibration alert function alerts you by vibrating the radio. The vibration patterns are also programmable (4 patterns x one time/repeat).
• The built-in the voice recorder records incoming calls up to a maximum of 8 minutes. When a specified 2-tone/5-tone signal or called by a specified ID (BIIS mode only) is received, the voice recorder automatically starts recording the message. You will not miss any important messages even when you are temporarily away from the radio. The recorded message will be preserved even when the radio is turned off. If you have a new message, the radio shows ¡§ *¡¨ icon on the display. You can manually start recording incoming calls and also your own message. It records up to a maximum of 8 minutes (Or up to 48 calls of 10 sec. recording time).
• The IC-F51V delivers a loud 700mW* audio output with the built-in BTL amp. The built-in audio compander provides clear, low noise communications. Improved bass characteristics also betters the audio quality. *Typical with internal speaker.
• When the radio is not operated for a preset period (1 to 255 min.), the radio sounds a beep and requires you to push the emergency button. If the emergency button is not pushed for a preset time (1 to 255 sec.), an emergency signal automatically transmits and informs your co-worker or dispatcher that something may have happened to the individual worker.
• Up to 10 hours of operating time with the supplied 1700mAh lithium-ion battery pack. (Tx: 5%; Rx:5%; Stand by:90% with power save on)
• The radio has outstanding protection against dust and water that is equivalent to IP67. The radio can withstand submersion in 1m depth of water for up to 30 minutes and has dust-tight construction that prevents the ingress of dust. The battery connectors made with anti-corrosion metal surface which is surrounded with a rubberized layer.
• Maximum 128 channels can be programmed into the radio in 8 channel groups.
• The radio has 7 progammable buttons including the red emergency button on the top of the radio. The individual volume control and channel selector provide easy and convenient operation.
• Use the built-in CTCSS, DTCS, 2-Tone, 5-Tone, DTMF autodial and BIIS signaling capabilities to set up your talk group or selective calling. The radio can decode ten 2-Tone codes or eight 5-Tone codes on a channel. When a matched tone is received, the following actions are programmable for each code. Bell icon, Answer back call, Beep sound, Auto transmit, Radio Stun/Kill/Revive, Voice recorder, Vibration alert
• The 5-Tone signalling (encoder/decoder) gives you selective calling, quiet stand-by and other convenient functions with programming. The radio “stun” function disables a radio over the air and the “revive” function restores the stunned radio.
• Channel spacing: 12.5/20/25Khz; PLL channel step: 2.5, 3.125Khz (VHF); 5, 6.25Khz (UHF)
• Built-in noise reduction for crystal clear communication
• The IC-F51V/F61V has a built-in inversion type* voice scrambler which provide securer conversation. *The inversion type voice scrambler is not compatible with UT-109/UT-110 type voice scrambler.
• 2-step power save
• Normal and priority scan
• New scanning features have been added allowing easier migration from other brand radios to Icom radios. The radio has 17 scanning list memories. Each scanning list consists of memory channels to be scanned and scanning type settings. Scanning type settings are selectable from normal scan or priority scans. The priority scan allows you to monitor one or two priority channels, while scanning other channels.
• In the regular mode scan, you can select a scanning list independent to the channel setting. However, in the mode slave setting, the scanning setting is dependent on the operating channel. When you change the operating channel, the scanning list automatically changes to that channel setting. It is convenient when you move to a different operating area and change an operating channel, you don't have to change the scanning setting.
• The Tx (Transmit) channel is the channel selected when you push the PTT button while scanning. It can be programmable per scanning list. The start channel, last detected channel, priority and pre-programmed channel are selectable. In addition, display setting while scanning is also programmable.
• The talk back function allows you to transmit on the channel detected when scanning stops or scanning resumes after a preset time, prior to the Tx channel setting. The talk back timer beep alerts you of the end of the talk back time with a beep sound. You can easily make a quick response with this function.
- Nuisance delete ... You can temporarily delete a busy channel from the scanning list.
- Monitor key action ... You can stop a scan when pushing the monitor button.
- Backlight at Stop Scan ... Automatically turns on the LCD backlight when the scan stops.• Low battery alert
• Power ON password
• Internal VOX for hands-free operation (optional VOX compatible headset are needed)
• Optional GPS hand microphone for sending location data
• Equivalent to MIL-STD 810 C, D, E, and F requirements